BEST WAYS TO INCREASE FUEL TANKERS AND REDUCE ACCIDENTS ON ROADS
The number of occurrences of falling off the road and causing fire to damage costly properties and killing people within have been on a large scale, at least every year about ten to twenty of such incident happens across the whole state in , this has created a lot of panic among the road users whenever a tank is passing, and majority of these occurrences are the ones loaded with product.
A critical look at the possible causes of this problem in regard to the design of the tank and its truck has revealed some flaw in design according to the state of Nigerian environment and its roads condition, which is not the same with the countries such design is applied. So we need to design things according to the condition of our environment, not the way it is in the western world.
From the research conducted below are the suggestions that would reduce the falling of the vehicle by increasing its on the roads:
WITH IMPROVEMENT ON THE SUSPENSIONS
The of the need to be streamlined to create a reduced effect on the truck when there is a gallop of the product in the tank. Though there is a normal and standard gap in which fuel are built but in the case of roads where most fuel and other heavy vehicles do fall off the road for the reason of instability while on . This has given a cause for concern into the design aspect and the factors put in place by the engineers while the truck.
Consider the two diagrams below:
Looking at the figures above you will quickly discover the difference in the two , FIGURE A is the current design employed by most engineers, while FIGURE B is a design I believe is better to help reduce the rate which fall on Nigerian roads.
Considering the design in FIGURE A, the is built with equal diameter in four cardinal axis which according to newton’s law of gravity, the of gravity acting downward on the truck is small when compared to the one in FIGURE B , this will go a long way to keeping the truck balanced on the ground, when the law of pressure is applied which states that the forces acting on a body when divided by the area it is acting will give the pressure on that body, then FIGURE B is the recommended design due to its eclipse shape that balances on the ground with its larger diameters facing upwards and downwards. Therefore the gravitational is able to act in a larger area than FIGURE A.
A look at FIGURE B will show the improvement in the suspension method between the and the body that should be another area of concern. A good suspension method should give each independent way of adjusting in any pothole without affecting the other.
The addition of more is another way of creating since the load in the tank can now be shared with other thereby prolonging the lifespan and making it easy to carry the tank comfortably.
Taking a look at FIGURE you will discover that the tank has two in each position, which make it six in the three positions.
But when another consideration is given to FIGURE B you will discover that it has four in each position, totally twelve in the three position. This design is very good and create the more rigid look and balance when the truck will be fully loaded.
The recent technology that enables door to detect an approaching and use the detection to trigger an electric motor to rotate a clockwise direction and make the door to open and stay open until the detection of the disappears, then it will trigger the electric motor to rotate in anti-clockwise direction cause the door to close pending until next time another will be detected. I love that technology since my friend did it as his final year project and it worked perfectly, controlling and securing the movements and activities at the entrance to the department. This same technology can be employed in the to be able to quickly detect an approaching at the location of the so as to automatically trigger a high reduction of speed at a particular distance as the truck is coming near the , this can be achieved by having the sensors mounted directly on the two sides of front location to detect in the form of objects or and trigger an electric motor to control the truck speed even while the driver is unaware. This design becomes important as most of the that fall occur due to while trying to across some .
THE TANK NEEDS MORE SPACING ACCORDING TO THE NEW TANK DIAMETER
Taking a critical look at the two figures A & B of , you will observe the difference in the stings, FIGURE A has its about 12 feet apart from each other because probably the uniform diameter of the tank is 12 feet, so the were meant to have the same position as the .
But consider the FIGURE B where the tank is in ellipse shape therefore under the same volume of tank the larger diameter should be around 14feet to 16 feet which mean the are to be separated apart for the same range which is either 14 feet or 16 feet apart depending on how properly the ellipse shape was designed, bearing in mind that the more the larger diameter, the more stable the tank becomes.
GAP BETWEEN THE TRUCK AND TANK SHOULD NOT BE HIGH
Another thing to put into consideration is the gap that exist between the truck and the truck carrying it, when the gap is much it create more dragging effect on the truck whenever the tank tilts to a particular angle as a result of gallops or , the same happens to the tank when the truck encounters , hence the case is vice versa.
Taking a look at the figure a & b, you will discover that the gap that exists between the tank and the truck in much in FIGURE A, while at FIGURE B it is less. The figure B will experience less effect on the event of encountering an obstruction on the road than Figure A.
BENT CORNERS SHOULD BE PASSED WITH LESS SPEED
Though this is an advice to the drivers particularly to always through a bent corner with low speed considering the length of the tank and its truck a good will be needed for it to turn at bent corners properly. Some fallen had been discovered that they are trying to divert in a particular direction with and due to the effect coming from the angular velocity in loaded the truck was swigged into a nearby bush which causes the whole body to fall inside any bush near the road.
THE HIGHEST TILTING DEGREE SHOULD BE DETERMINED AND THE METER ATTACHED TO AREA VISIBLE TO THE DRIVER
After the tank according to design in FIGURE B and attaching it to the truck the next thing that is very important is to conduct a tilting test on the whole of the vehicle and determine the highest degree of tilt that the truck and tank can collapse, when it is done attach a tilting meter at the body of the truck at a visible location to the driver. if there is a digital device to assist in this such as inclinometer and any other available then fix it at the front of the vehicle at the driver’s desk where other meters are, but in a situation where such device is not accessible than using a pointer fixed at a point to swing Freeling like a pendulum bob will help to determine the tilting angles of the vehicle at any moment. Consider the diagram below:
Considering Figure C, at the place the pointer is facing they are calibrated with different ranges of degrees, such that any tilting of the tank causes the pointer to indicate the degree.
A mechanical engineer, an NDT inspector, Graphic designer & Web developer, I love and sharing of knowledge for human intellectual development, especially relating to fields, environment, and science trending updates.
“Engineeringall.com” is a , to do so; use the “PUBLISH YOUR ARTICLE” page at the MENU to share your personal ideas, researched knowledge, or discovered incidents, etc.to those in the & & the general online communities across the globe. If you love this post please share using the social buttons below.