Skip to content

Basic Ways to Know The Thickness Of Aluminum Roofing Sheet

Colorless short span aluminum roofing sheets looking like alloyed zinc roofing sheet

Understanding the Various Ways to Know The Thickness Of Aluminum Roofing Sheet

The conflict that usually arises in any building contract has to do with the quality of materials used in the building which contradicts the materials specified on paper.

There had been cases where contractors feel bad due to the wrong accusations from their clients.

The accusation could come based on the low knowledge of the client relating to the building materials. In most situations, the conflict could lead to loss of trust and subsequent denial of any future contract by the client.

alloyed roofing zinc
Know The Thickness Of Aluminum Roofing Sheet: alloyed roofing zinc

In such a case, it is the duty of any builder and contractor to educate their clients on the materials to be used in the building, their costs, their different brands, quality, and the best one to be used in the building project.

Know The Thickness Of Aluminum Roofing Sheet: short span aluminum roofing sheet
Know The Thickness Of Aluminum Roofing Sheet: short span aluminum roofing sheet

That should be done before embarking on the contract, to be on the safer side it is good to show a sample of your quoted materials to your client for taking of pictures and market comparison of prices if your client wants.

5 Reasons Building Contractors Could Use Substandard Material

Know The Thickness Of Aluminum Roofing Sheet
Know The Thickness Of Aluminum Roofing Sheet

The reason conflict of using substandard material for contracts could be that;

  1. The contractor wants to make an excess gain, hence; avoiding carrying the client along in the process of carrying out the project.
  2. The contractor may have underquoted the costs of materials in the contract during the contract bidding and may resort to looking for substandard and cheaper materials to meet up instead of informing the client of the initial mistake.
  3. The contractor may have used some part of the money meant for the contract to solve personal problems.
  4. The client may be the fault, especially when the client is taking advice or suggestions from another builder or expert that is not the contractor. In such case; there may be a conflict of accusing the contractor of not following the real plan unduly, so it is always good to keep a copy of materials and procedures listed on your contract agreement for reference purpose.
  5. Unforeseen accidents or damage could cause conflict between the two parties.

But besides all these and many other factors, there are cases where the contractor will deliberately want to cheap and dupe the client because, the client may not have knowledge about the materials and the processes involved in the contract, this is worst when the client is a very busy person.

The cheating that occurs in the roofing of buildings is usually done when a long-pan aluminum roofing sheet is involved.

The reason for this is because the contractors will measure the areas that need the roofing and quote the number of long-pan aluminum that the space need, and such quotation may not be clear to the client.

Hence; it is possible to overquote the number needed to the detriment of the client who will pay for it.

Another way to cheat on the client in aluminum roofing is through the use of the wrong thickness.

Basic Ways to Know The Thickness Of Aluminum Roofing Sheet

A good contractor will clarify the client with different ranges of aluminum roofing sheet thickness in the market and their cost while a bad contractor will not do that.

The thickness of aluminum roofing sheets in most Nigerian markets ranges from 0.7mm to 1mm thickness, the thicker the roofing sheet, the costlier it will be.

So bad contractor could quote 1mm thickness during contract bidding and use 0.8mm thickness without the knowledge of the client.

The bad aspect of this is that even though the contractor show you the sample of the 1mm thickness of the aluminum roofing sheet, it will be hard to know if it is the same 1mm when 0.8mm is used for the roofing.

The best way to catch such bad contractors is to employ a measure strategy on the thickness of the samples and to achieve that you will need micrometer or vernier calipers.

Hiring a small micrometer screw gauge or vernier caliper wouldn’t cost more than N300, or you may just acquire one at the cost of N1500 to ensure you are not cheated.


Place the spaced jaws in-between in a vertical position and insert a small part of the aluminum roofing sheet in them screw the gauge until it tension lightly with the surfaces of the roofing sheet.

Then read the millimeter on the calibration side to know how many millimeters(mm) thickness the roofing sheet is having.

If you have no knowledge of reading the measuring instrument calibration, consider buying the digital type for direct reading.

5 thoughts on “Basic Ways to Know The Thickness Of Aluminum Roofing Sheet”

  1. Please different between full gauge and non full gauge roofing sheet.
    I found 0.45mm at full gauge and I found 0.45mm non full gauge but same aluminium roofing sheet has the same thickness

  2. Hey There. I found your blog the use of msn. That is a really well written article. I will be sure to bookmark it and come back to read extra of your helpful info. Thank you for the post.

  3. Thank you for any other informative site. Where else could I am getting that kind of info written in such a perfect approach? I’ve a undertaking that I’m just now running on, and I have been on the glance out for such information.

Leave a Reply

Your email address will not be published. Required fields are marked *

error: Content is protected !!