Tractors such as the type shown in the above are mainly used to drag other mechanized in agricultural such are ploughing , digging , harvesting , etc. their function is mostly to provide the mechanical needed to move these , for that reason a single can be used with different by simply detaching the one fixed earlier from it back hook provided for such coupling and replacing it with a new meant for another purpose.
There are different sizes of tractors and their sizes determines their power output and the type of they can do, the sample shown above is one of the smallest sizes of tractors meant for subsistence agriculture or small scale production of commercial agriculture, the reason is because of its power output and the quantity of it can do per hour which may become a big stress for large-scale commercial agriculture that may be having about 4 hectares of land for a single farm, in such using this size of will cause stress to the operator and the of the .
However, there are some notable things you need to observe and be conscious of when working with this type they are:
The coupling of the is usually located at the back where it established with other functional attached to it, it had been found that when heavier is attached to it, problems will develop at that coupling location, the causes is not restricted to that, another cause of coupling problem could arise when the is carrying heavy load or subjected to high stress while performing it function, as a result, the coupling part will experience gradual deformation which is due to the malleability nature of the metals used in the manufacturing, in a severe situation the spaces and gaps creates by the deformation of shapes will start causes the coupling to make noise and jerking sound as the is moving forward with the , such will also result in little lack of equilibrium in the tractor’s .
To ensure durability to the coupling always apply grease when necessary and ensure proper tightening of the bolts and nuts, and consider the output of the attached to be according to the standard capacity of the manufacturer of the .
Ground level can cause very high instability to the when moving the , because the were made to move on rough surfaces without restriction due to the high torque and momentum of the used in , yet like every other it needs a particular range of ground level to function effectively and any level above such range may cause irregular and galloping and miscalculations if the it is moving is meant to perform any function within an interval of time.
Soil texture has to do with how strong or soft a soil is, the can function effectively in a strong & dry soil, but if there is a heavy rainfall that made the soil to become extremely slippery working with the will consume more with low output, while still giving stress to the . When such condition occurs it may be necessary to allow the soil to lose its slippery property either through sunlight or other means before proceeding with the farming operation.
THE SOIL PREVIOUS USE
Knowing the previous use of the land you are working on will help in knowing the dangers within, if a residential or public place was cleared up and mapped out for farming purpose, it is necessary to consider that some sharp objects capable of causing great injury to the may be located beneath the soil, so during the ploughing activity such objects may be located at the shallow level beneath the soil, if such consciousness is not there you may just move the over them and incur injury to its .
One thing diesel engines hate is to operate until the whole diesel in the tank finishes. In fact, it is a bad idea to operate any diesel engine and allow it to go off as a result of finished diesel, while this may be tolerated for few times, the bad news is that you may just wake up one day and discover that the engine will not be able to start even when there is diesel in the tank. The major reason for this action is because diesel has higher viscosity than petrol and it do carry impurities though these impurities are not solid looking particle rather they may be molecule inclusion during refining, and the bottom part of diesel is where all of these impurities settle, if you allow the diesel to finish in the tank it will drag those impurities which usually through the filters and enter into the injector to the injector nozzle, hence making ignition of the impossible until the nozzle is changed or serviced. So keeping eyes on the level in the will keep you away from stress resulting from failure.
Water plays an essential role in any and one of the roles is to help in controlling the operating of , if you allow the to lack water in the it will lead to interval overheating and wearing of dynamic parts of the . Keeping the water level will prolong the lifespan.
THE JOINTS RIGIDITY
Looking at the photo you can visually see that there are lots of joints that are used in the assembling, due to the nature of that the performs, it is very necessary to the whole joints of the and using torque range to tighten the loosed bolts and nuts at each joint before operating the .
Your opinion and contributions are welcomed, please drop them through the comment form, update trends, and our forums.
Originally posted 2017-07-30 02:20:59.
A mechanical engineer and an NDT inspector by profession. However, I love blogging and sharing of knowledge for human intellectual development, especially relating to engineering fields, environment, and science trending updates. “Engineeringall.com” is a platform for any individual with similar passion, to do so; use the “PUBLISH YOUR ARTICLE” page at the MENU to share your personal ideas, researched knowledge, or discovered incidents, etc.to those in the engineering & & the general online communities across the globe. If you love this post please share using the social buttons below.